Fundamental Plumber Guide for Installing a Bathtub
Fundamental Plumber Guide for Installing a Bathtub
Blog Article
Are you currently trying to locate ideas around Tools You Need to Install a New Bathtub ?
Installing a tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is easily available, the project can relocate speedily; if you have to open a wall to get rid of the old tub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to leave the old tub and set in the brand-new one. Make sure you have actually certified on your own for the task and also fit trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will aid you install a new bath tub in your bathroom if you have currently acquired a new bathtub as well as do not need to alter the plan of your previous water supply pipes.
Your devices and also product checklist must consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, turn on the taps to drain any water staying in the system. The process of removing the existing faucets can be quite troublesome because of the restricted accessibility that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in place with the producer given backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous kind needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the called for position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bath tub up until the level reads level.
To set up faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the supply of water and inspect all joints as well as new pipework for leaks and also tighten them if needed. Fill the tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Setup
First of all, the supporting structure supplied with the bathroom should be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final placement.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, causing difficulties with wetness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the tub is in use. The sealer can split fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on Tools You Need to Install a New Bathtub ? Write feedback further down. We will be interested to find out your insights about this review. We hope to see you back again in the near future. Are you aware of someone else who is interested by the niche? Feel free to promote it. Many thanks for going through it.
Affordable? Call now! Report this page